pcl_test

问题1、2

@echo off
setlocal enabledelayedexpansion
for /f "tokens=1-3* delims=-" %%a in ('dir /a-d /b *.dxf') do (
if "%%d" == "" (
set "n=%%b"
md "!n:~,6!\" 2>nul
move "%%a-%%b-%%c" "!n:~,6!\"
) else (
set "n=%%c"
md "!n:~,7!\" 2>nul
move "%%a-%%b-%%c-%%d" "!n:~,7!\"
)
)
复制代码

问题3 论坛自行搜索 定时

511182890

回复 31# pcl_test


    问题2：
AD101-D1-PKD1818-140背料(2米62)倒顺.dxf
AD101-D1-PKD1822横排-140副料(1米57)双向.dxf
AD101-D1-PKD-140背料(2米62)倒顺.dxf
AD101-D1-P0LD-140背料(2米62)倒顺.dxf
FT505-G1201三位-AA-142副背料(0米75)双向.dxf
FT505-G1956-AA-142副背料(0米75)双向.dxf
怎么做个命令移动到
PKD1818\AD101-D1-PKD1818-140背料(2米62)倒顺.dxf
PDK1822\AD101-D1-PKD1822横排-140副料(1米57)双向.dxf
PDK\AD101-D1-PKD-140背料(2米62)倒顺.dxf
P0LD\AD101-D1-P0LD-140背料(2米62)倒顺.dxf
G1201\FT505-G1201三位-AA-142副背料(0米75)双向.dxf
G1956\FT505-G1956-AA-142副背料(0米75)双向.dxf





之前那命令没有-AA
现在多加了-AA

511182890

回复 31# pcl_test


       问题2：
AD101-D1-PKD1818-140背料(2米62)倒顺.dxf
AD101-D1-PKD1822横排-140副料(1米57)双向.dxf
AD101-D1-PKD-140背料(2米62)倒顺.dxf
AD123-D1-P0LD-140背料(2米62)倒顺.dxf
AD145-D1-PKD三位-140背料(2米62)倒顺.dxf
AD167-D1-P0LD横向-140背料(2米62)倒顺.dxf
FT505-G1201三位-AA-142副背料(0米75)双向.dxf
FT505-G1956-AA-142副背料(0米75)双向.dxf
怎么做个命令移动到
PKD1818\AD101-D1-PKD1818-140背料(2米62)倒顺.dxf
PDK1822\AD101-D1-PKD1822横排-140副料(1米57)双向.dxf
PDK\AD101-D1-PKD-140背料(2米62)倒顺.dxf
P0LD\AD101-D1-P0LD-140背料(2米62)倒顺.dxf
PKD\AD145-D1-PKD三位-140背料(2米62)倒顺.dxf
P0LD\AD167-D1-P0LD横向-140背料(2米62)倒顺.dxf
G1201\FT505-G1201三位-AA-142副背料(0米75)双向.dxf
G1956\FT505-G1956-AA-142副背料(0米75)双向.dxf

511182890

回复 31# pcl_test


    大神再帮一个忙
ABD101-D1-P0KD.DSN
AD101-D1-P0D.DSN
AD101-D1-PKA1101.DSN
ACD101-D1-PKA3333无刀眼.DSN
处理为
P0KD\ABD101-D1-P0KD.DSN
P0D\AD101-D1-P0D.DSN
PKA1101\AD101-D1-PKA1101.DSN
PKA3333\ACD101-D1-PKA3333无刀眼.DSN